simplfication http://www.youtube.com/watch?v=RWTwTLj6m6c

Well, I used a transformer and it didn't help, in this configuration I took out the passive components and it will charge another 250Mah battery battery in about 1 minute, but it still isn't fast enough for hovering. If batteries are charged very fast, they'll cook up to a higher voltage than 9V, which is perfect, 8.4 doesn't work at all. After a while, they may be extremely high voltage cooked[frozen] from little use and high charge. http://www.4shared.com/document/BDqJ-mDk/voltage_multiplier2.html
The simplification might be to use a 9.6V pack and just let it die until you reach exactly 9V so it works on its own without extra circuits. Nice slices of copper is how to get around the pico ohm, although those are just for efficiency.

It provides about 11.46 Kwatts at 41.3 seconds and 5.5w at 21.65 seconds, I would say about 11Kwatts before the batteries won't recharge anymore, time for a generator capacitor. http://www.deerso.com/14ODX5UG_COPPER_COIL477222-details.aspx?src=gbs

parts list for dual battery regenerator http://www.bing.com/videos/watch/video/roses-are-free-by-ween/7208e0da050ec9bf99947208e0da050ec9bf9994-1130585

Mainly, its a good idea to pick parts that are easy to solder, surface mount pins are close to impossible to solder, so I picked the parts out. It's good to leave long 4in. leads, all the stuff should fit if its wrapped around, use electrical tape to isolate groupings. The batteries can drop a charge spontaniously.

1 x 10 pack PNP transistors http://cgi.ebay.com/NEW-10-X-2SA1015-2SA1015Y-PNP-Transistor-/220623714318?pt=LH_DefaultDomain_0
2 x 5pk diode http://www.newark.com/multicomp/bzw04-31/diode-tvs-36v-400w/dp/08N6246
1 x 50k->1M ohm resistor
7 x 100mH inductors http://www.newark.com/bourns/rlb1314-103kl/dp/61J7946
2 x 100nF capacitor array http://www.newark.com/murata/gnm214b11c104ma01d/capacitor-array-0-1uf-16v-0805/dp/97K0564
1 x 10pk 10uF capacitor http://www.newark.com/multicomp/mcgpr35v106m5x11/capacitor-10uf-35v-capacitor-10uf/dp/38K4684
2 x 5pk 50uF capacitor http://www.newark.com/multicomp/np16v476m6-3x11/capacitor-n-p-47uf-16v-capacitor/dp/13M5153?matchedProduct=47uf&whydiditmatch=rel_1
7 x 100uF capacitor http://www.newark.com/rubycon/16yk100m5x11/capacitor-alum-elect-100uf-16v/dp/38M1391
2 x 1K ohm resistor array http://www.newark.com/jsp/search/productdetail.jsp?SKU=55R1978&CMP=AFC-GB100000001
1 x 2 9v and bay http://battery-superstore.com/T228-Plugin-Compact-Charger-with-2/M/B001A3JSMW.htm

First Over Unity Circuit http://www.youtube.com/watch?v=P7AMMj32G8Y

I was trying to figure out how to get the hover shoes to levitate with the 9V. I built this circuit, its highly tuned and unchangable, it only works this way. Also, its not flawed, which is why its built this way, there's lots of flaws in the program. The voltage accross the resistor in the diagram below just keeps growing as the current from the output battery remains constant.
http://www.4shared.com/document/lVpHIPEt/_2__voltage_multiplier.html

It gets 5x the watts with household AC